| |
Wood Flooring Installation
Introduction
Different installation methods for wood flooring include
Nail Down, Staple Down, Glue Down,
and Floating/Free-Float. One problem when deciding
to purchase a wood floor, is "which installation method will be right for
me?" With several different methods to choose from, it can be confusing to
say the least. We're going to discuss this subject in detail and hopefully
it will help you with your decision.
The first thing you need to do, would be to find out what type of sub-floor
you currently have. I am not talking about the existing carpet, vinyl, or
ceramic tile you may have on the floor, I am referring to the actual base
floor itself, which in most cases would be plywood or concrete. By
determining what type of sub-floor you have, you will automatically narrow
down your options. If you have a plywood sub-floor, you can choose any of
the installation methods. If you have a concrete sub-floor, you will not be
able to use the nail or staple down method without going through what we
would consider to be a ridiculous amount of preparation.
Let's take a look at each on of the installation methods individually, where
they would apply, and where they may be most beneficial.
Nail Down Installations
This type of method is used primarily when installing a solid wood floor.
Since solid wood floors are usually thicker, they need to be nailed in order
to stay in place properly. As we discussed in our article titled Solid or
Engineered Flooring, which is right for me, solid wood flooring has a
tendency to expand and contract more than engineered flooring. With the in
mind, using a glue down method would prove to be a huge mistake with a solid
floor. There are some exceptions to this rule. One such exception would be
the Natural Reflections series by Bruce. While most solid wood floors are
3/4" thick, this product comes 5/16" thick. Since the product is much
thinner than a conventional solid wood floor, you experience less expansion
and contraction. This product can be stapled or glued down.
Nowadays, most consumers are getting away from the solid wood flooring in
favor of the engineered products because of their superior stability. There
are some situations however, where the solid wood flooring might be
beneficial. One such application might be if you have existing solid wood
floors in certain areas of your home, and you want to extend that flooring
into other areas. As we mentioned previously, if you would like to learn
more about solid wood floors versus engineered, read our article titled
Solid or Engineered Flooring, which is right for me.
|
D.I.Y.
NOTE: Nail down installations are not generally recommended as a
Do-It-Yourself project. This type of installation requires certain
professional tools and experience. |
 |
Staple Down Installations
This installation method has become more popular since engineered wood
flooring has grown in popularity. This installation method is mainly used
with engineered plank or strip wood floors over a plywood or wood sub-floor.
Certain wood floors require specific types of staple sizes. It is
recommended that you find out what type of staples are required for the
series of flooring you have selected. The staple down method has been proven
to be a good choice for certain product lines.
D.I.Y. NOTE: Staple down installations would be
recommended as a Do-It-Yourself project for someone with a moderate amount
of skill using power tools. In most cases, a special stapler is required
which can sometimes be rented.
Glue Down Installations
This installation method is most common when installing an engineered strip
or plank wood floor over a concrete sub-floor. If done properly, a glue down
installation is a very stable one. A lot of people with plywood sub-floors
have also learned that a glue down installation can also be beneficial. The
reason being is that it can be quieter than a staple down install with less
creaking when the floors expands and contracts.
One major drawback to the glue down installation can be the evenness of the
sub-floor, or correct sub-floor preparation. If you install an engineered
wood floor using the glue down installation method, and your sub-floor is
not flat, you are asking for some serious future problems. One of those
problems will be something known as "popping". This is where the bond of the
glue breaks loose in a low spot of the floor, and that section is no longer
attached to the sub-floor. Another problem can be improper bonding. This is
usually caused when the sub-floor was not cleaned properly and the glue you
are spreading on the floor is actually being spread over the dust and/or
dirt. This can also cause the bond to be broken. Yet another problem with
this installation method is the use of a non-approved floating or flashing
compound. I know I probably just lost you so let me explain. If your
sub-floor is not even, you will need to use a cement type compound to flash
or float that area in order to make it flat in preparation for the wood
floor installation. After you install a wood floor using the manufacturers'
recommended adhesive, that adhesive has a tendency to shrink and pull the
wood floor tighter down to the sub-floor. If the correct flashing or
floating compound is not used, when the adhesive shrinks, it can literally
rip the compound right off the floor, leaving you with a section or sections
that is not bounded.
|
D.I.Y. NOTE: Glue down installations are recommended
for someone that has some experience working with the preparation methods
described above. If you have a sub-floor that is flat, or only requires
minor preparation, the glue down installation is not that difficult.
|
 |
Floating / Free-Float
Installations
This installation method has grown tremendously in popularity over the last
few years. It has become known as one of the most stable and forgiving
installation methods available. The reason this installation method is so
stable, is because it is not attached to the sub-floor whatsoever.
The free-float installation method is most common with products known as
engineered longstrip wood floors. This product type is somewhat of a panel
system. Most products in this category come in boards approximately 8" by
96", and may vary in size depending on the manufacturer. Here's what makes
this product, and the way it's installed so unique. These products are
installed by first laying down an underlayment, usually foam or a plastic
and foam combination, and then the wood flooring is laid on top of that
underlayment, a bead of water based glue is applied to the tongue and groove
per the manufacturers' instructions, the boards are tapped together using a
tapping block, and the excess glue is wiped off with a damp cloth. That's
it!
Why is this type of installation more stable? Simple. With the other
installation methods we've discussed, each plank or strip is installed
individually. When the floor expands and contracts, which it most definitely
will, the size of the gaps between those planks or strips tends to get
larger and then tighter. This can be a major issue in areas where the
climate changes dramatically from season to season. With the free-float
installation, the boards are glued together, not down, so when the floor
expands and contracts, it does so as one big floor as opposed to individual
units. Additionally, since these boards are glued together, there are no
gaps whatsoever between the boards. Yet another stability advantage is the
fact that these boards are not attached to the sub-floor. You will not
experience any of the popping or creaking you might with one of the other
methods. The foam underlayment also helps absorb some of the minor
imperfections in the sub-floor, so the exact evenness of the sub-floor is
not as crucial with this type of installation. We would like to point out
that while the free-float method does require slightly less effort in the
way of sub-floor preparation, each manufacturer has their own guidelines as
to the sub-floor requirement that you must follow in order for the warranty
to be valid.
|
D.I.Y. NOTE:
The free-float installation method gets high marks as a very
do-it-yourself friendly install type. Someone with little or no
experience can easily tackle an installation using this method. If you
are looking to save on the installation cost and install a wood floor
yourself, we would suggest this as a first choice over other install
methods. |
 |
|
